2g 3g portable ozone generator
Description
2g 3g portable ozone generator
Description
Our HY-002 ozone generator is an portable odor neutraliser that is designed to eliminate pungent odors and will kill up to 99.9% of airborne viruses in a variety of locations. The ozone emitted by HY-002 will destroy harmful micro-organisms with that it comes into contact with and will break down odor causing compounds effectively neutralising the unpleasant smells they produce at the source.
Specification
| Item | Unit | HY-002-2g | HY-002-3g |
| Ozone output | G/Hr | 2 | 3 |
| Power | W | 60 | 80 |
| Voltage | V/HZ | AC220/110V,50/60HZ | |
| Concentration | Mg/L | 15-25 | |
| Gas feeding | / | Dry clean air | |
| Dimension (L*W*H) | CM | 23*18*40 | |
| Unit weight | Kg | 6 | 6.5 |
| Cooling method | / | Air cooling | |
| Air flow | L/h | 16 | |
| Attachments | Sets | Silicone tube, fuse, etc | |
| Color | / | Silver | |
Application
| No. | Applications |
| 1 | Space sterilization |
| 2 | Animal smell removal |
| 3 | Keep food in fresh condition |
| 4 | Baby production disinfection |
| 5 | Waste water treatment,aquarium water freshen |
| 6 | Wash fruit and vegetable, residual pesticide removal |
| 7 | Living room, bedroom, kitchen, WC, car, air purification |
| 8 | Remove formaldehyde, benzene and other harmful gas in furniture,new house |
Details
Installation
| No. | Installation Guide |
| 1 | The ozone generator should be installed in low humidity circumstance with temperature between 0℃ to 43℃ and good condition of air circulation for heat dispersing. |
| 2 | The ozone generator should be installed close to the mains. Lengthening the cable is not suggested. |
| 3 | To keep appropriate condition for heat dispersion, the ozone generator should be installed far from the heat source enough and the barriers around with distance no less than 0.6 meters. |
| 4 | Please ensure the feeding gas and ozone outlet is correctly connected. |
| 5 | The ozone generator and oxygen generator would be installed 1.2 meters above the floor, and the ozone delivery line must be 1 to 2 meters high than the mixer of gas and water,2meters high than the water holding jar to prevent water sucked in. |
Fault detection and analysis
| Equipment status | Causes | Solutions | Remarks |
| No power | 1. Power plug loose | Plug in 220V/50HZ power | |
| 2. No 220V voltage | |||
| No gas output from outlet | 1. Regular inspection to know whether the internal wiring joint is loose | 1.Cut down the power，then opening the back cover to check the pipes or wirings | Be careful！Must cut down the power to open the back cover. |
| 2.Whether a block in the pipes | 2.Turn on the air pump switch | ||
| 3. Whether air pump switch was turned on or not | |||
| Gas supply regular, no ozone output | 1. Whether ozone switch is turned on or not | 1.Turn on the ozone switch button | |
| 2.Concentration | 2. To adjust the concentration button | ||
| Adjustment is 0 levels. | 3. Check the electrocircuit. | ||
| 3.Control panel is out of control | 4.To change the electrical discharge | ||
| 4.Electrical discharge is damaged | |||
| Case leakage | 1.Ungrounded electrical application at your local | Power supply should be ungrounded electrical application | |
| 2.Humidity | 2.To install the ozone generator in dry place | ||
| Operating machine’s fuse burn-out, or tripping | 1. Short Circuit | 1. Check the electrocircuit | |
| 2 Electrical discharge is damaged | 2. To change the electrical discharge | ||
| Water store inside the machine | 1. A backflow of water from operating water treatment into the ozone generator tube | 1.To dry inner ozone generator tube | In case of water into machine during the running, it is necessary to stop the machine Immediately to check and remove the faults |
| 2.Humidity | 2. To dry the inner machine box | ||
| 3.Undisposed air source | 3.Drying process for air source |
